Duratherm XLT-120 Heat Transfer Fluid
Duratherm XLT-120 heat transfer fluid is engineered for long-term operation in heat transfer applications requiring precise temperature control ranging from -120°F up to 150°F (-84°C to 65°C).
Ideal for cryogenic applications Duratherm XLT's ecomomical cost and wide operating temperature also makes it well-suited for heating and cooling applications found in the food processing, pharmaceutical and chemical industries.
Trouble-Free Operation
Duratherm XLT-120 heat transfer fluid does not require monitoring of concentration or additive levels.
Longevity
Duratherm XLT-120 heat transfer fluid utilizes our exclusive additive system for long-term, trouble-free operation at any temperature, high or low.
Environmental
Duratherm XLT-120 heat transfer fluid is plant and user friendly. Low odours, high flash point and no SARA reportable substances makes XLT the wise choice for worker health and safety.
Disposal
After its extensive service life, Duratherm XLT-120 heat transfer fluid can be disposed of through local waste oil recycling programs. Check your local regulations.
| Duratherm XLT-120 Properties | ||
|---|---|---|
| Appearance: clear liquid, slight yellow tint | ||
| Maximum bulk/use Temp. | 150°F | 65°C |
| Minimum bulk/use Temp. | -120°F | -84°C |
| Flash Point ASTM D92 | 120°F | 49°C |
| Fire Point ASTM D92 | 140°F | 60°C |
| Viscosity ASTM D445 | ||
| cSt at -40°F / -40°C | 8.5 | |
| cSt at 32°F / 0°C | 4.5 | |
| cSt at 150°F / 65°C | 1.3 | |
| Pour Point ASTM D97 | -130°F | -90°C |
| Density ASTM D1298 | lb/ft3 | g/ml |
| at -40°F / -40°C | 54.1 | 0.866 |
| at 32°F / 0°C | 53.5 | 0.856 |
| at 150°F / 65°C | 50.8 | 0.813 |
| Carbon Residue ASTM D189 | 0.005 | % Mass |
| Sulphur Content X-RAY | <.001 | weight % |
| CU Strip Corrosion ASTM D130 | 1a | |
| Thermal Conductivity | BTU/hr F ft | W/m K |
| at -40°F / -40°C | 0.080 | 0.138 |
| at 32°F / 0°C | 0.079 | 0.136 |
| at 150°F / 65°C | 0.076 | 0.131 |
| Heat Capacity | BTU/lb F | kJ/kg K |
| at -40°F / -40°C | 0.460 | 1.925 |
| at 32°F / 0°C | 0.471 | 1.971 |
| at 150°F / 65°C | 0.520 | 2.177 |
| Vapor Pressure ASTM D2879 | psi | kPa |
| at 60°F / 15°C | 0.00 | 0.00 |
| at 100°F / 38°C | 0.02 | 0.13 |
| at 150°F / 65°C | 4.31 | 29.71 |
| Distillation Range ASTM D2887 | 10% | 181°F (83°C) |
| 90% | 546°F (285°C) | |
*The values quoted are typical of normal production. They do not constitute a specification | ||
What they're saying...
"The heat transfer appears to be the best it's ever been " — R. Barnett
"You manufacture products that perform exactly as advertised, which is not always the case in the marketplace." — H. Blair
" We used to use Paratherm ... it had a tendency to sludge up. I noticed with Duratherm though that it does not sludge up at all." — B. Corbett
"We were thoroughly impressed with DuraClean Ultra. The system was spotless, and all of the hard build-up was completely removed in only 6 hours" — M. Fransiscovich
"You proved once again that while your goal is to grow. It's through honest customer service and great products." — K. Rose
"The oil still looks as clear as it did when we first put it into use." — J. Thomas
In only two weeks the hard pieces of burnt oil (COKE) had liquefied and we were able to clean the lines out with just air pressure. — E. Disanto
